Mazda RX-7 (1992-2002 (FD)) Wiper Blades 20 inches / 500 mm + 20 inches / 500 mm + 18 inches / 450 mm Rear Beam Set
Wiper blade sizes guaranteed to fit your vehicle.
.png)
What Size Wiper Blades for Mazda RX-7 1992-2002 (FD)?
The correct wiper blade sizes for a 1992-2002 (FD) Mazda RX-7 are:
- Driver Side: 20 inches / 500 mm beam blade
- Passenger Side: 20 inches / 500 mm beam blade
- Rear: 18 inches / 450 mm rear wiper
WiperBlade.com.au - Find Your Size
Driver Side
20 inches / 500 mm
Passenger Side
20 inches / 500 mm
Rear
18 inches / 450 mm
Vehicle Details
| Make | Mazda |
| Model | RX-7 |
| Year / Variant | 1992-2002 (FD) |
| Kit Type | Front & Rear |
Compatible Variants
Mazda RX-7 1992-2002 (FD) Replacement Wiper Blades
Front & Rear Kit
- Free Delivery Australia-wide
- Perfect Fitment Guarantee
- Premium Quality Wipers
- Easy 30-Second Install
Popular item — selling fast for Mazda owners
"Found the right size instantly and the UNIWIPER blades are great quality. Free delivery was a bonus!"
Mark H.
Verified Customer
Why Replace Your Mazda RX-7 Wipers?
Worn wiper blades are more than an annoyance — they're a safety hazard. Here's what happens when you delay replacement.
Dangerous Visibility
Streaks and blind spots reduce your view by up to 40% in rain, especially at night.
Annoying Squeaking
Hardened, cracked rubber scrapes across glass making an irritating noise every sweep.
Wrong Size = Wasted Money
Buying the wrong size means wasted trips and refunds. We guarantee the correct fit for your Mazda.
Before
- Streaks and smears blocking your view
- Constant squeaking and juddering
- Replacing every few months
- Guessing which size fits your car
After UNIWIPER
- Crystal clear visibility in all conditions
- Whisper-quiet operation every time
- Premium blades that last 12+ months
- Guaranteed perfect fit for your Mazda RX-7
Get the Right Wipers in 3 Easy Steps
No guesswork, no wrong sizes, no wasted trips.
Find Your Size
We've already looked it up — your Mazda RX-7 sizes are shown above.
Order from UNIWIPER
Click "Buy Now" to order the exact blades — with free delivery Australia-wide.
Install in 30 Seconds
Simple clip-on design. No tools needed. Clear vision in under a minute.
What Drivers Are Saying
Trusted by thousands of Australian drivers.
"Found the exact size for my Corolla in seconds. Ordered from UNIWIPER and installed in under a minute. Massive upgrade from the cheap ones I had before."
Mark H.
2021 Toyota Corolla • Sydney
"No more squeaking! My old wipers were leaving streaks everywhere. The UNIWIPER blades are whisper-quiet and the free delivery was a nice bonus."
Sarah B.
2019 Mazda CX-5 • Melbourne
"Was always buying the wrong size at the auto store. This site told me exactly what I needed. Perfect fit first time and they last way longer."
James P.
2022 Hyundai Tucson • Brisbane
Our Triple Guarantee
Every UNIWIPER order comes backed by three promises, so you can buy with total confidence.
Perfect Fitment
Guaranteed to fit your Mazda RX-7 or your money back.
Free Delivery
Fast, free shipping to anywhere in Australia. No hidden fees.
Easy Install
Simple clip-on design. No tools, no mechanic. Done in 30 seconds.
Other Mazda RX-7 Variants
Installation Guide for Mazda RX-7 (1992-2002 (FD))
Fitting beam wiper blades to your Mazda RX-7 takes about 60 seconds per blade. No tools required.
-
1
Lift the wiper arm
Pull the wiper arm away from the windscreen until it locks in the upright service position. Do this one arm at a time to avoid the arm snapping back onto the glass.
-
2
Release the old blade
Most Mazda RX-7 models use a hook connector. Press the small tab on the underside of the blade, then slide the blade down the arm and off the hook.
-
3
Fit the new beam blade
Match the 20 inches / 500 mm blade to the driver side and the 20 inches / 500 mm blade to the passenger side. Slide the new blade onto the arm hook until you hear it click into place.
-
4
Lower and test
Gently lower the arm back onto the glass. Run the wipers once with a light water spray to confirm smooth, chatter-free contact across the full sweep.
-
5
Rear wiper
Your Mazda RX-7 also has a rear wiper (18 inches / 450 mm). Rear blades typically pull straight off the arm — check the connector type before ordering.
Why Upgrade from Mazda Dealership Wipers?
Mazda dealerships typically charge $150–$220 for a front pair of wiper blades — often the same rubber compound, at three times the price.
- × $150–$220 per pair
- × Book a service appointment, wait days
- × Labour fee even for a 60-second job
- × Same generic rubber, branded box
- ✓ Exact-fit sizes verified for your RX-7
- ✓ Delivered to your door, free Australia-wide
- ✓ Fit them yourself in under a minute
- ✓ OEM-quality beam construction, all-weather rubber
Fitment Guarantee for RX-7 (1992-2002 (FD))
Every size on this page has been cross-referenced against the factory service specification for the 1992-2002 (FD) RX-7. If a blade doesn't fit, we'll make it right.
Exact-fit verified
Sizes matched to the RX-7 arm hook and sweep pattern — not a generic year range.
30-day returns
Wrong size, changed your mind, doesn't clear the glass? Send it back within 30 days for a full refund.
Fast Australia-wide shipping
Order today, dispatched today. Metro delivery in 2–3 business days, tracked door-to-door.
Beam vs Traditional Blades for Mazda RX-7
Modern Mazda models ship from the factory with beam-style wiper blades for a reason — here's how they compare to the older frame-and-hinge design.
| Beam Blade (recommended) | Traditional Frame Blade | |
|---|---|---|
| Windscreen contact | Continuous spring-steel pressure across the full length | Pressure at 4–8 hinge points only |
| Highway performance | Aerofoil spoiler holds the blade down at speed | Lifts off the glass above ~90 km/h |
| Cold-weather use | Sealed frame — no hinges to ice up | Exposed joints can freeze and streak |
| Typical lifespan | 12–18 months | 6–9 months |
| Look on a modern Mazda | Low-profile, factory-correct | Bulky, dated silhouette |
The blades listed for your RX-7 above are premium beam-style — the same design Mazda fits at the factory. Scroll up to order the exact-fit set.